New Construction Plumbing in Kendall, FL

Inspection-Ready New Construction Plumbing Services in Kendall, FL

Guest House, ADU and Addition Plumbing in Kendall, FL

Guest houses and additions need plumbing that ties into the existing house without overloading old drain lines. We locate the existing sewer, check its condition with a camera and confirm there is enough fall to the new building. Supply lines can be branched from the main house or run as a separate service, based on distance and pressure. We also handle the trenching between structures and restore the yard when we are done.

Plumbing Rough-In Services in Kendall

The rough-in phase is the backbone of your new construction plumbing system. This involves installing all underground and in-wall piping before concrete is poured and walls are closed. We carefully lay out and connect all water supply, drain, and vent pipes according to architectural plans and local Kendall codes. Using high-quality PEX or copper piping, we ensure secure, leak-free connections that will serve your property for decades.

Residential New Build Plumbing in Kendall

For new homes, our residential new construction plumbing includes the complete installation of water supply lines, drain waste vent systems, and gas lines. We confirm proper sizing and pressure for all fixtures, from showers to kitchen sinks, while accounting for local water quality and potential foundation movement. Many wells in Florida produce water with a sulfur smell or high iron, which often calls for filtration to protect fixtures and appliances. Our process includes careful planning to prevent future slab leaks or drainage issues tied to the soil under your lot.

New Construction Plumbing Cost Planning in Kendall, FL

Plumbing for a typical new single-family home often runs about 4 to 8 percent of total build cost, depending on fixture count and finish level. A modest three-bedroom home often lands between $12,000 and $25,000, while custom homes with multiple suites and outdoor kitchens run higher. Choices like a manifold PEX system, a recirculation loop and fixture grade move the number most. We break the bid out by phase so you can see clearly where the money goes.

Water Heater and Recirculation Installation in Kendall, FL

New homes commonly use tank water heaters in the garage, basement or utility room, or tankless units on an exterior wall. We size the heater to your bathroom count and install gas or electric connections, venting, an expansion tank and drain pan where required. Many owners add a dedicated recirculation line during rough-in, which is far cheaper than retrofitting later. Many wells in Florida produce water with a sulfur smell or high iron, which often calls for treatment to protect fixtures and appliances. If treatment makes sense for your water, we suggest planning space for a softener or filter loop at the same time.

Underground and Under-Slab Plumbing in Kendall

The underground phase sets the drain, waste and vent layout that every fixture in the house will depend on. We trench, bed and slope PVC or ABS drain lines at a minimum quarter inch per foot and protect every pipe that passes through the slab or foundation with sleeves. Nearly all homes in Florida sit on concrete slabs over sandy soil, so leaks under the slab are a frequent and costly repair. We compact bedding carefully and avoid rigid points that could stress the pipe as the ground moves. Each line is water tested and left visible for the inspector before your concrete contractor pours.

Gas Piping for New Homes in Kendall

We size and install gas piping for ranges, water heaters, furnaces, fireplaces, pool heaters and outdoor kitchens. Black iron and CSST systems are both available, and CSST is bonded per manufacturer and code requirements. We calculate total BTU load and pipe length so every appliance gets enough pressure even when everything is running together. The system is pressure tested and inspected before the utility sets the meter.

Final Trim and Fixture Setting in Kendall

At trim we install toilets, faucets, garbage disposals, dishwashers, ice maker boxes and laundry connections. We work with fixtures from Moen, Delta, Kohler, American Standard and the other brands builders commonly specify, or with owner-supplied fixtures. Every fixture is checked for flow, drainage and leaks, and angle stops are set straight and tight. We finish by running every fixture at once to confirm the system drains and vents properly under load.